No matter what you call them – guide combs, clipper guards, attachment guards or attachment combs – these simple accessories are tools that help you measure the length of hair that you are cutting away. They are designed to fit onto your clipper’s blades.
How to Use Guide Combs & Which Size to Use
1
Guide combs attach to the clipper and are designed to cut hair at a certain length.Guide combs help you get specific hairstyles, such as the Fade Cut . Without the attachments, these hairstyles would be hard to achieve.
2
There are different guide comb sizes/lengths. The smaller the number, the shorter the cut. The larger the number, the longer the hair will be.For example, if you use a #2(1/4") guide comb, you will be left with hair that is a quarter of an inchin length. Whereas a #8 (1") guide comb will leave your hair at 1-inch in length.
Wahl guide combs are measured in inches. See the chart below.
Using the Upward Rocking Motion is sometimes the best way to blend different lengths of hair in different sections of the head to achieve a finished look. To do this, carefully pull the clipper away from the scalp in fluid strokes as you cut upward to blend the hair from one length to the next.
Make Sure to Blend Your Hair
With fine hair, you will need to do more blending because it tends to show different cut lengths more easily.
The smaller the number, the shorter the cut.The larger the number, the longer the hair will be. For example, if you use a #2 (1/4") guide comb, you will be left with hair that is a quarter of an inch in length. Whereas a #8 (1") guide comb will leave your hair at 1-inch in length.
With the bristles of the comb up, comb the hair upward from the back or toward you from the front, and stop before the hair leaves the comb. Run the clipper across the comb to cut the hair to the desired length.
The majority of hair trimmers come with eight different sizes of guard. The clipper guard AKA haircut number refers to the length of hair that is left after the clipper has been used, with each number representing one eighth of an inch of hair. This means that the lower the number, the shorter the hair, and vice versa.
Snap-on combs are attached to the clipper's blade, so they “soften” the cutting edge with their rounded ends. Even if your hand slips or you haven't mastered your technique, clipper guards protect your dog from being poked by the blade and getting hurt.
Avoid combs with sharp edges or seams, as they can cause unnecessary friction and damage to the hair shaft. Metal combs can be overly harsh on the hair, leading to breakage and damage. They can also create static electricity, which further contributes to hair frizz and breakage.
A clipper guard does have teeth and act something like a rake in pulling hair up it's teeth to the blades. But it also is like a spacer in that it lifts the blades up and off of the scalp. The sizes are the amount of lift or spacing the guard has. #1 is 1/8 of an inch, #4 is 4/8 or 1/2 inch, #8 is 8/8 or 1 inch..
Simple clipper cuts are also often referred to using numbers. These refer to the guard length used on the blades and therefore the subsequent hair length created. #1 – 3.4mm, #2 – 6.4mm, #3 – 9.5mm, #4 – 12.7mm, #7 – 22.2mm, #8 – 25.4mm.
To style thick hair, you should use a fine-tooth comb.For thin and fine hair, you can use a pintail comb. Pintail combs are also best for creating an up-do and down-do hairstyle. Trimming hair: For trimming hair, we recommend using a cutting comb (trimming comb), as these combs have both wide and closely spaced teeth.
Amazon.com: Wahl Professional #2 Guide Comb Attachment - 1/4" (6.0mm) - 3124-001 - Great for Professional Stylists and Barbers : Beauty & Personal Care.
An example number 3 haircut is a crew cut. You can have the sides cut short with a number 3 but leave the top longer. The sides and back in this hairstyle are usually faded, while the top is left with more length and styled how you'd like it.
Clipper blades are available in a variety of different lengths and tooth patterns to achieve different trim styles and coat lengths. They are differentiated by blade numbers; blades with higher numbers actually cut the coat shorter, and blades with lower numbers leave the coat longer.
Introduction: My name is Clemencia Bogisich Ret, I am a super, outstanding, graceful, friendly, vast, comfortable, agreeable person who loves writing and wants to share my knowledge and understanding with you.
We notice you're using an ad blocker
Without advertising income, we can't keep making this site awesome for you.
