Choosing the Right Wire Nuts for Electrical Connections (2024)

While doing almost any kind of electrical wiring in your home, you'll likely run into wire connectors used to make a variety of different circuit wire connections for light fixtures, outlet receptacles, switches, and other devices. The most common type of wire connectors are little round little plastic caps, often called wire nuts, that twist over the bare ends of wires to make tight connections. Wire nut connections are reversible—they can be unscrewed in the future in the event that you need to replace any device.

Wire Connectors AretheBest

If you ever find wires joined with electrical tape, or the wires are twisted together and then wrapped with electrical tape, get rid of the tape and join the wires with wire nuts. Never use tape in place of wire nuts—it's simply not secure enough, and it's vulnerable to damage. Some people like to use wire nuts and wrap them with tape. This fine to do, but you probably won't find any wire nut manufacturers advising you to do it.

There are also push-fit-type wire connectors, which make very secure connections and are easy to use. But they are more expensive than wire nuts, and loosening them in the future when you need to remove a device can be more difficult.

How They Work

Standard wire nuts are roughly conical in shape and usually have ridges on their sides so your fingers can get a good grip. Some types have little side wings instead of ridges. Inside the plastic cone is a littlesquare-cut spring that provides tension on the wires to hold them securely. As you tighten the wire connector by twisting it, the spring draws tighter around the wires. Variations onclassic twist-type wire nuts include push-in wire connectors (you push the straight wire ends into holes), waterproof wire connectors (usually gel-filled to keep out moisture), and butt-splice connectors (for joining wires end to end).

How to Use Them

Always follow the manufacturer's instructions, as techniques vary by product. But here's the standard procedure:

1. Strip about 1/2 to 3/4 inch of insulation from the end of each wire, using a wire stripper. Be sure to use the right hole in the stripper so that you don't cut into the metal of the wire.
2. Hold the wires together, so their ends are aligned.
3. Fit the appropriate size of wire nut over the wire ends and push into the wires while twisting the nut clockwise. Twist until the nut is as tight as you can get it, and there is no bare wire showing below the nut. You can also give the nut a final short twist with a pair of linesman pliers if you feel the nut isn't tight enough.
4. Give each wire a little tug to make sure it is securely held by the nut. If a wire pulls out at all, remove the nut and start over.

Some people, including many electricians, like to twist the wires with lineman pliers in a clockwise direction before applying the wire connector. They feel that itmakes for a more secure connection and may help keep the wires together in situations where vibration can possibly work the nut loose. In any case, it's best to follow the manufacturer's directions, which often does not include pre-twisting the wires together.

• Tip: When joining a solid-copper wire to a stranded-copper wire, strip the stranded wire about 1/8 inch more than you do for the solid wire. The stranded tends to wrap around the solid wire when you twist on the nut, so the extra length helps make a strong connection. Before putting on the wire nut, align the wires so the edges of the insulation are even, and the stranded wire ends extend past the ends of the solid wire.

Sizes

Wire connectors come in different sizes and colors. The color indicates the size, quantity, and type of wires the nut can accommodate. The wrong size nut is one that is either too large or too small for the size and number of wires being connected. Eitherway, this means a weak connection, which is potentially dangerous (loose wires start fires). The packaging for all wire nuts includes a chart that tells you what color of nut to use with the wires you're connecting. For example, for a particular manufacturer, a gray nut may work for a minimum of two 22-gauge stranded wires up to a maximum of two 16-gauge solid wires. The next size up (perhaps a blue nut) may be suitable for two 22-gauge solid wires up to a maximum of three 16-gauge solid. Overlap in the sizing chart is common; just make sure you're within the range for the color you're using. Colors vary by manufacturer, so always consult the chart on the packaging.